Skip to content
Book a demo
Suits
Belt loader (conveyor belt loader)
When
Before use
Items
51, in 28 sections

Identity

  1. Scan the START tag; confirm the GSE ID plate matches the asset on screenScan or type the code · out of service if it fails
  2. Airside vehicle permit / airside registration label present, legible and in dateDate · out of service if it fails

Walk-around

  1. Walk around the whole unit: no new body damage, cracks, sharp edges or loose panelsPass, fail or not applicable · photo every time
  2. No fluid leaks under the unit (oil, coolant, hydraulic, fuel, electrolyte)Pass, fail or not applicable · out of service if it fails · photo every time

Tyres & wheels

  1. Tyres: no cuts, bulges, exposed cord or flats; tread adequate; solid tyres not chunkedPass, fail or not applicable · out of service if it fails
  2. Wheel nuts all present; no rust trails or movement on nut indicatorsPass, fail or not applicable · out of service if it fails
  3. Tyre pressures (pneumatic only) within OEM range (limits set per asset)Reading against your limit

Fluids

  1. Engine oil level between marksPass, fail or not applicable
  2. Coolant level at or above minimum (check cold)Pass, fail or not applicable
  3. Hydraulic oil level within sight-glass rangePass, fail or not applicable
  4. Fuel level / battery state of charge sufficient for the shiftReading against your limit
  5. AdBlue/DEF level above warning (diesel with SCR)Pass, fail or not applicable

Electrical

  1. Battery secure, terminals covered, no swelling or damage; charging lead and plug undamaged and disconnected before movingPass, fail or not applicable · out of service if it fails
  2. No warning lamps or active fault codes after start-upPass, fail or not applicable

Lights

  1. Headlights, tail, brake and indicator lights workPass, fail or not applicable
  2. Flashing/rotating amber beacon(s) work and visible 360°Pass, fail or not applicable · out of service if it fails · photo every time
  3. Belt-head work lights (night ops) workPass, fail or not applicable

Audible

  1. Horn worksPass, fail or not applicable
  2. Reversing alarm (tonal or broadband) sounds when reverse selectedPass, fail or not applicable · out of service if it fails

Vision

  1. Mirrors present, secure, uncracked, adjusted; camera image clearPass, fail or not applicable

Brakes

  1. Service brake test at walking pace: stops straight and promptlyPass, fail or not applicable · out of service if it fails
  2. Parking brake holds the unit (slope or drive-against test per OEM)Pass, fail or not applicable · out of service if it fails

Steering

  1. Steering free, no excessive playPass, fail or not applicable · out of service if it fails

Cab

  1. Seat secure; seat belt latches and retracts; operator presence switch worksPass, fail or not applicable · out of service if it fails

Controls

  1. Drive and work controls return to neutral; labels legible; interlocks (e.g. drive inhibit when raised/stabilised, neutral-start) workPass, fail or not applicable · out of service if it fails
  2. Emergency stop(s) cut drive/hydraulics; reset correctlyPass, fail or not applicable · out of service if it fails

Fire

  1. Extinguisher present in bracket, pin and seal intact, gauge in green, service tag in datePass, fail or not applicable · out of service if it fails
  2. Extinguisher service date (from tag)Date · out of service if it fails

Aircraft protection

  1. Proximity sensors / auto slow-down / anti-collision system passes self-test or test approach (where fitted)Pass, fail or not applicable · out of service if it fails

Markings

  1. Reflective tape and conspicuity markings present and clean; GSE ID number visible both sidesPass, fail or not applicable

Speed

  1. Speed limiter operating (max speed not exceeded in test, or limiter seal intact)Pass, fail or not applicable · out of service if it fails

FOD

  1. Cab, decks and trays free of loose items that could fall or blow onto the apronPass, fail or not applicable
  2. Cleanliness: windows clean, steps not slippery, no rubbishPass, fail or not applicable

Documents

  1. Logbook / operator card and emergency contacts present; open defects reviewed in appPass, fail or not applicable

Maintenance

  1. Hour meter / odometer readingReading against your limit
  2. Next service due (date or hours) not exceeded: computed from I35 and workshop dataPass or fail
  3. Annual / statutory inspection label in dateDate · out of service if it fails

Exhaust

  1. No excessive smoke; exhaust and spark arrestor (where required) intactPass, fail or not applicable

Radio

  1. Two-way / airport radio works (where fitted or required)Pass, fail or not applicable

Belt

  1. Belt surface: no tears, missing cleats, frayed edges or lacing failurePass, fail or not applicable · photo every time
  2. Belt runs both directions, tracks centrally, stops on release of controlPass, fail or not applicable · out of service if it fails
  3. Belt E-stops at both ends (ground and head) stop the beltPass, fail or not applicable · out of service if it fails

Boom

  1. Boom raises and lowers smoothly at both ends; holds position with no creepPass, fail or not applicable · out of service if it fails
  2. Lift cylinders and hoses: no leaks or chafingPass, fail or not applicable · out of service if it fails

Handrails

  1. Handrails raise, lock and are not bent; walkway non-slip intactPass, fail or not applicable · out of service if it fails

Aircraft interface

  1. Head-end bumper(s) present, secure, not splitPass, fail or not applicable · out of service if it fails · photo every time
  2. Head-end proximity/slow-down sensor and approach speed limit work (where fitted)Pass, fail or not applicable · out of service if it fails
  3. Stabilisers/outriggers (where fitted) deploy; drive interlocked when deployedPass, fail or not applicable · out of service if it fails

Guides

  1. Side guides/side rails at belt head present and not bentPass, fail or not applicable

Rollers

  1. Belt rollers and drive roller free of debris, no noisePass, fail or not applicable

Sign-off

  1. Operator declares the unit fit for use, or unfitChoose one · out of service if it fails

Checked by ______________________   Date and time ______________   Unit ______________

No limit is shown here on purpose: set each from the maker’s manual or your own procedure. A starting point: change the items to match your procedure before you rely on them.

How it differs from the baggage tractor / tug pre-use check

39 of its 51 items are the same on both. This one adds belt-head work lights (night ops) work, belt surface: no tears, missing cleats, frayed edges or lacing failure, belt runs both directions, tracks centrally, stops on release of control, belt E-stops at both ends (ground and head) stop the belt, boom raises and lowers smoothly at both ends; holds position with no creep and 7 more. It leaves out cab doors/curtains secure; wiper works, bumpers / rubbing strips / aircraft-contact pads present, secure, not split or compressed flat, rear tow hitch pin/jaw latches and pin retained, front hitch (if fitted) secure, LPG cylinder secured, valve and hose intact, no gas smell; cylinder test date in date and 2 more.

What this checklist asks for

Takes the unit out of service

As the starter is set, a fail on any of these takes the unit out of service until the defect is cleared. You can change what any item does.

  • Scan the START tag; confirm the GSE ID plate matches the asset on screen
  • Airside vehicle permit / airside registration label present, legible and in date
  • No fluid leaks under the unit (oil, coolant, hydraulic, fuel, electrolyte)
  • Tyres: no cuts, bulges, exposed cord or flats; tread adequate; solid tyres not chunked
  • Wheel nuts all present; no rust trails or movement on nut indicators
  • Battery secure, terminals covered, no swelling or damage; charging lead and plug undamaged and disconnected before moving
  • Flashing/rotating amber beacon(s) work and visible 360°
  • Reversing alarm (tonal or broadband) sounds when reverse selected
  • Service brake test at walking pace: stops straight and promptly
  • Parking brake holds the unit (slope or drive-against test per OEM)
  • Steering free, no excessive play
  • Seat secure; seat belt latches and retracts; operator presence switch works
  • Drive and work controls return to neutral; labels legible; interlocks (e.g. drive inhibit when raised/stabilised, neutral-start) work
  • Emergency stop(s) cut drive/hydraulics; reset correctly
  • Extinguisher present in bracket, pin and seal intact, gauge in green, service tag in date
  • Extinguisher service date (from tag)
  • Proximity sensors / auto slow-down / anti-collision system passes self-test or test approach (where fitted)
  • Speed limiter operating (max speed not exceeded in test, or limiter seal intact)
  • Annual / statutory inspection label in date
  • Belt runs both directions, tracks centrally, stops on release of control
  • Belt E-stops at both ends (ground and head) stop the belt
  • Boom raises and lowers smoothly at both ends; holds position with no creep
  • Lift cylinders and hoses: no leaks or chafing
  • Handrails raise, lock and are not bent; walkway non-slip intact
  • Head-end bumper(s) present, secure, not split
  • Head-end proximity/slow-down sensor and approach speed limit work (where fitted)
  • Stabilisers/outriggers (where fitted) deploy; drive interlocked when deployed
  • Operator declares the unit fit for use, or unfit

Takes a number against your limit

The limit is yours to set; until you do, the number is kept with no pass or fail.

  • Tyre pressures (pneumatic only) within OEM range (limits set per asset)
  • Fuel level / battery state of charge sufficient for the shift
  • Hour meter / odometer reading

Needs a photo every time

Taken live on the phone and kept with the answer.

  • Walk around the whole unit: no new body damage, cracks, sharp edges or loose panels
  • No fluid leaks under the unit (oil, coolant, hydraulic, fuel, electrolyte)
  • Flashing/rotating amber beacon(s) work and visible 360°
  • Belt surface: no tears, missing cleats, frayed edges or lacing failure
  • Head-end bumper(s) present, secure, not split

Questions about this checklist

What does the belt loader (conveyor belt loader) pre-use check cover?

51 items in 28 sections: identity, walk-around, tyres & wheels, fluids, electrical, lights and 22 more.

What happens when an item fails in Escudo Aviation?

As the starter is set: 28 items take the unit out of service when they fail; the rest are recorded. You can change what any item does. A failure asks for a photo on 22 items, and the defect goes to the people who fix it.

Does the belt loader (conveyor belt loader) pre-use check come with limits?

No. 3 items take a number against a limit (tyre pressures (pneumatic only) within OEM range (limits set per asset), fuel level / battery state of charge sufficient for the shift and hour meter / odometer reading), and each limit is yours to set from the maker’s manual or your own procedure. Until you set one, the number is still recorded.

Run it on the phone instead of paper

Open it from the unit’s tag, with or without signal. A failed item becomes a defect with a photo and sets the status as your template says.

Send us your own version of this check

We load your vehicles, zones and the templates you choose, you validate them in your own words, and your crews start checking. Tell us about your airport.